Nanocrystalline transformer core provider in China? Transmart Industrial’s nanocrystalline core series include multiple types , For example, nanocrystalline cut cores,nanocrystalline toroidal cores,nanocrystalline tape wound cores,nanocrystalline powder cores, etc.Good materials, advanced production technology, and fine manufacturing techniques are used in the production of nanocrystalline core. Transmart nanocrystalline core suppliers & manufacturers designs transformer core material with to keep it outstanding among similar products. See extra details on https://www.transmart.net/nanocrystalline-cores. Soft magnetic materials are those materials that are easily magnetised and demagnetised. They typically have intrinsic coercivity less than 1000 Am-1. They are used primarily to enhance and/or channel the flux produced by an electric current. The main parameter, often used as a figure of merit for soft magnetic materials, is the relative permeability (µr, where µr = B/ µoH), which is a measure of how readily the material responds to the applied magnetic field. The other main parameters of interest are the coercivity, the saturation magnetisation and the electrical conductivity.
Since silicon steel has the above advantages, why not use the whole silicon steel as the iron core and process it into a sheet? This is because the sheet iron core can reduce another iron loss – “eddy current loss”. When the transformer works, there is alternating current in the coil, and the magnetic flux generated by it is of course alternating. This changing magnetic flux produces an induced current in the iron core. The induced current generated in the iron core flows in a ring in a plane perpendicular to the magnetic flux direction, so it is called eddy current. Eddy current losses also heat the core. In order to reduce the eddy current loss, the iron core of the transformer is stacked with silicon steel sheets insulated from each other, so that the eddy current passes through a small section in the narrow and long circuit, so as to increase the resistance on the eddy current path; At the same time, the silicon in silicon steel increases the resistivity of the material and reduces the eddy current.
The common mode inductor using nanocrystalline core material can well suppress the peak voltage, protect sensitive components, and reduce the motor shaft voltage. Because of the unique characteristics of nanocrystalline core, it has been well used in some high-power system industries. Electric energy meter, power meter, ammeter, electric measuring equipment and other instrument fields. Various power current transformers in power transmission and distribution monitoring system. Leakage protection, relay protection, servo motor protection, fire monitoring, etc Current and voltage data sampling, etc.
Transmart amorphous core manufacturer & supplier is mainly engaged in the production and sales of amorphous core materials. The amorphous core transformer is one of Transmart Industrial’s multiple product series.Transmart Industrial’s amorphous C-core is manufactured in strict accordance with relevant national standards. Every detail matters in the production. Strict cost control promotes the production of high-quality and priced-low product. Such a amorphous transformer is up to customers’ needs for a highly cost-effective product. Discover additional details on https://www.transmart.net/.
Now, the test of magnetic core material loss of power frequency power transformer is carried out under sine wave voltage with distortion less than 2%. The actual power frequency power grid distortion is 5%. In this case, the loss of iron-based amorphous alloy increases to 106% and that of silicon steel increases to 123%. If the high-order harmonic is large and the distortion is 75% (such as power frequency rectifier transformer), the loss of iron-based amorphous alloy increases to 160% and the loss of silicon steel increases to more than 300%.
After surface insulation treatment, the magnetic core is evenly mixed with the binder, pressed and annealed. There are basically three ways to obtain nanocrystalline powder: amorphous strip crushing after annealing and crystallization, mechanical alloying and molten alloy atomization. At present, mechanical alloying is still in the laboratory research stage. A few companies produce amorphous strip crystallization in small quantities in China, but it is unable to expand the market due to cost reasons. Compared with other methods, molten alloy atomization method has high efficiency and low cost. Its disadvantage is that the amorphous content of the powder is low and the loss is high.